The Hanging Cabinet Design
The metal angle section lends itself very well to build many different cabinet design, including container furniture such as cabinets, whether placed as a wall hanging on the floor. Be adapted to many sites, such as a cellar, a pantry, a laboratory, etc. It is, in this case, a fairly large structure, but not too high or deep, in the form of parallelepiped, from a frame of angle section 40 x 40mm slotted wings and whose walls are covered with veneer 0 fibers. On the front doors are sliding panels in the relevant guidelines. Was suspended and fixed to the wall with sturdy metal anchors.
The cabinet frame house
The first thing to do is cut to size of all – the parts that intervene.
It is done with a hand saw for metal arc or with – a machine angle album: the deburring. With the first work will be somewhat tiresome, as if you can have the second and an appropriate disc for cutting, sawing operation will be much more expeditiously. Keep in mind that the slicing disc eat 5 to 8mm in each cut, losses are calculated by marking and cutting.
He always make the cut on the outside so that the pieces were to the full extent that is required. Having also in mind that it will have to polish any burrs caused in cutting. Resorting to a file or the same machine if you have safety in handling and is sure that no damage will occur in the selvedge. Start assembling the racks are rectangular base and top of the cabinet. Angular bars longer measured 2.000mm, while the short lengths are 400mm, the unions are achieved with nuts and bolts 6 x 18mm. In the triangle of the base is screwed into the four corners of the respective amounts (whose length is also 400mm). Check with the team the proper perpendicularity of these amounts to the base. In the center of the four major strips is mounted an upright consisting of a pair of vertical profiles whose length is about 400mm (ie, somewhat less for being able to place inside the frame). These amounts are as a T to provide a robust and supportive of the whole structure and at the same time, lead to a split in the cupboard. Moreover, this solution will use bars and pieces of a meter attached at its head, fixed with screws on the wings of the T.
The walls of the closet
The walls of plywood (or fibreboard) Now that the structure obtained with the angular profile is now ready to be assembled, to apply the board walls (8 mm plywood or fibreboard hard it may be thicker than and even already be painted). Cut the elements of the board to the correct size so they can enter and fit snugly in the respective sites. Put each of these elements in place and mark the holes will be made, so that they correspond with the slots of the profile, in order to drive the screws that retain (the same kind that is used to join sections together Profile).
The cabinet assembly
Skip to setting each element assembly with four or more screws. It is desirable to insert washers to avoid damaging the board with the screw heads. Prepare four sliding doors (from 550mm wide and 360mm high) carefully polishing the upper and lower edges, which should slide easily in the guides. Now place the guides in aluminum or brass (or plastic) with dual channel inside which has a width slightly larger than that of the boards. Be found in hardware stores, DIY and materials for windows, which cut to the extent requested. In case you have to buy into strips, which may be cut to size using a metal blade. The slides are placed in the front guide and the other on the back. Guides to 900 mm long is applied to the board of the fund angular profile 10 mm above, by focusing on the respective openings. Fixation is achieved simply with glue. Glued in position for other guides on the top panel. When the doors located in the directory, check that they slide properly. Then place in closed position can be fixed at its ends, the appropriate distance, four knobs that can be done simply with chunks of wood. For fixing, use a bit of white glue and drive a nail through the inside.
The cabinet assembly
Now you can proceed to final assembly. Place in position above the doors in their guides, so they are vertical, and then mount the upper frame (it is likely to have to ask for help from another person) so that the guides are correctly placed on the panels sliding.
But it would first mount the upper frame and then sliding panels, as they can be easily introduced into the upper guide: just place them above the bottom channel without overhang. The panel height is such that, once entered, can not exit the top guide channel. Apply the screws that fix the roof of the upper frame using the holes previously carried out, and tighten the nuts. Now only is the whole set of furniture to the wall.
Fastening the cabinet to the wall
It is achieved with the use of anchors of metal type. They are highly effective diameter of 14mm, fitted with hinge and nut on the end wall surfaces and that, once fixed on the wall, ensuring a stay completely safe. Drill the holes at appropriate points and insert the plugs.
Attach the hinges to the cabinet and screw them to be definitive.
Relevant Posts
Tags: a machine angle album, chunks of wood, cut to size using a metal blade, Fastening the cabinet to the wall, four sliding doors, metal arc, mount the upper frame, sliding panels, The cabinet frame house, the center of the four major strips, the form of parallelepiped, The Hanging Cabinet Design, The walls of plywood, The walls of the closet
